We remove the unused status_send_fd, and rename status_send_sync (it
should only be used for that case now).
We add a status_setup_async(), and wire things internally to use that
if it's set up: status_setup() is renamed status_setup_sync().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We use the fourth value (size) to determine the type, unless the fifth
value is suppled. That's silly: allow the fourth value to be a typename,
since that's the only reason we care about the size at all!
Unfortunately there are places in the spec where we use a raw fieldname
without '*1' for a length, so we have to distingish this from the
typename case.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
aka "BOLT 3: Use revocation key hash rather than revocation key",
which builds on top of lightningnetwork/lightning-rfc#105 "BOLT 2,3,5:
Make htlc outputs of the commitment tx spendable with revocation key".
This affects callers, since they now need to hand us the revocation
pubkey, but commit_tx has that already anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
All the daemons will use a common seed for point derivation, so drag
it out of lightningd/opening.
This also provide a nice struct wrapper to reduce argument count.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We should start watching for the transaction before we send the
signature; we might miss it otherwise. In practice, we only see
transactions as they enter a block, so it won't happen, but be
thorough.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is a bit tricky: for our signing code, we don't want scriptsigs,
but to calculate the txid, we need them. For most transactions in lightning,
they're pure segwit so it doesn't matter, but funding transactions can
have P2SH-wrapped P2WPKH inputs.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The spec 4af8e1841151f0c6e8151979d6c89d11839b2f65 uses a 32-byte 'channel-id'
field, not to be confused with the 8-byte short ID used by gossip. Rename
appropriately, and update to the new handshake protocol.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Only minor changes, but I add some more spec text to
lightningd/test/run-commit_tx.c to be sure to catch if it changes
again.
One reference isn't upstream yet, so had to be commented out.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now we've tested it:
1. open_channel needs to write response to REQ_FD not STATUS_FD.
2. recv_channel needs to send our next_per_commit, not echo theirs!
3. print the problematic signature if it's wrong, not our own.
Cleanups:
1. Return the message from open_channel/recv_channel for simplicity.
2. Trace signing information.
3. More tracing messages.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Or for blackbox tests --gdb1=<subdaemon> / --gdb2=<subdaemon>.
This makes the subdaemon wait as soon as it's execed, so we can attach
the debugger.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The requirements for accepting the remote config are more complex than
a simple min/max value, as various parameters are related. It turns
out that with a few assumptions, we can boil this down to:
1. The valid feerate range.
2. The minimum effective HTLC throughput we want
3. The a maximum delay we'll accept for us to redeem.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell