We don't actually process onion messages here any more (they moved to
connectd), but the flag and object files were still linked.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This contains the zeroconf stuff, with funding_locked renamed to
channel_ready. I change that everywhere, and try to fix up the
comments.
Also the `alias` field is called `short_channel_id`.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Changelog-Changed: Protocol: `funding_locked` is now called `channel_ready` as per latest BOLTs.
We need a record of the channel account before you start sending
payments through it. Normally we don't start allowing payments to be
sent until after the channel has locked in but zeroconf does away with
this assumption.
Instead we push out a "channel_proposed" event, which should only show
up for zeroconfs.
it's nice to know what node your channel was opened with. in theory we
could use listpeers to merge the data after the fact, except that
channels disappear after they've been closed for a bit. it's better to
just save the info.
we print it out in `listbalances`, as that's a great place account level
information
We don't push out a coin_move for a channel open until it's locked in,
but this causes problems for channels that close before they're locked.
So if we go the "close before locked in" route, we push out a channel
open event.
These will get a blockheight of 0, if we haven't seen the
funding transaction in a block yet.
The only places which should call try_reconnect now are the "connect"
command, and the disconnect path when it decides there's still an
active channel.
This introduces one subtlety: if we disconnect when there's no active
channel, but then the subd makes one, we have to catch that case!
This temporarily reverts "slow" reconnections to fast ones: see next
patch.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This allows us to detect when lightningd hasn't seen our latest
disconnect/reconnect; in particular, we would hit the following pattern:
1. lightningd says to connect a subd.
2. connectd disconnects and reconnects.
3. connectd reads message, connects subd.
4. lightningd reads disconnect and reconnect, sends msg to connect to subd again.
5. connectd asserts because subd is alreacy connected.
This way connectd can tell if lightningd is talking about the previous
connection, and ignoere it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Before this patch:
1. connectd says it's connected (peer_connected)
2. we tell connectd we want to talk about each channel (peer_make_active)
3. connectd gives us an fd for each channel, and we connect it to a subd (peer_active)
4. OR, connectd says it sent something about a channel we didn't tell it about, with an fd (peer_active)
Now:
1. connectd says it's connected (peer_connected)
2. we start all appropriate subds and tell connectd to what channels/fds (peer_connect_subd).
3. if connectd says it sent something about a channel we didn't tell it about, we either tell
it to hang up (peer_final_msg), or connect a new opening daemon (peer_connect_subd).
This is the minimal-size patch, which is why we create socket pairs in
so many places to use the existing functions. Many cleanups are
possible, since the new flow is so simple.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We have them split over common/param.c, common/json.c,
common/json_helpers.c, common/json_tok.c and common/json_stream.c.
Change that to:
* common/json_parse (all the json_to_xxx routines)
* common/json_parse_simple (simplest the json parsing routines, for cli too)
* common/json_stream (all the json_add_xxx routines)
* common/json_param (all the param and param_xxx routines)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We used to agree up on the `minimum_depth` with the peer, thus when
they told us that the funding locked we'd be sure we either have a
scid or we'd trigger the state transition when we do. However if we
had a scid, and we got a funding_locked we'd trust them not to have
sent it early. Now we explicitly track the depth in the channel while
waiting for the funding to confirm.
Changelog-Fixed: channeld: Enforce our own `minimum_depth` beyond just confirming
We don't trigger on depth=0 since that'd give us bogus blockheights
and pointers into the chain, instead we defer until we get a first
confirmation. This extracts some of the logic from `lockin_complete`,
into the depth change listener (not the remote funding locked since at
that point we're certainly locked in and we don't really care about
that for bookkeeping anyway).
This is needed for us to transition to CHANNELD_NORMAL for zeroconf
channels, i.e., channels where we don't have a short channel ID yet.
We'll have to call lockin_complete a second time, once we learn the
real scid.
We locally generate an update with our local alias, and get one from
the peer with the remote alias, so we need to add them both. We do so
only if using the alias in the first place though.
We do this (send warnings) in almost all cases anyway, so mainly this
is a textual update, but there are some changes:
1. Send ERROR not WARNING if they send a malformed commitment secret.
2. Send WARNING not ERROR if they get the shutdown_scriptpubkey wrong (vs upfront)
3. Send WARNING not ERROR if they send a bad shutdown_scriptpubkey (e.g. p2pkh in future)
4. Rename some vars 'err' to 'warn' to make it clear we send a warning.
This means test_option_upfront_shutdown_script can be made reliable, too,
and it now warns and doesn't automatically close channel.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This doesn't have an effect now (except in experimental mode), but it
will when we support anchors. So we deprecate the use of those in the
close command too.
For experimental mode we have to avoid using p2pkh; adapt that test.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Changelog-Deprecated: JSON-RPC: `shutdown` no longer allows p2pkh or p2sh addresses.
We get some memleak reports because ld owns the subd, but once
the peer/channel is freed, there's no reference for the brief time
until the subd exits.
This happens for both opening and closingd. For openingd, the
peer owns it, for others (including dualopend) the channel owns it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is generally verboten now, since there can be multiple. There are a
few exceptions:
1. We sometimes want to know if there are *any* active channels.
2. Some dev commands still take peer id when they mean channel_id.
3. We still allow peer id when it's fully determined.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Changelog-Changed: JSON-RPC: `close` by peer id will fail if there is more than one live channel (use `channel_id` or `short_channel_id` as id arg).
More efficient to search a known peer than the whole set.
Also, move find_channel_by_id() from channel_control.c into channel.c
where we'd expect it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Generally this means converting a lazy "peer_active_channel(peer)" call
into an explicit iteration.
1. notify_feerate_change: call all channels (ignores non-active ones anyway).
2. peer_get_owning_subd remove unused function.
3. peer_connected hook: don't save channel, do lookup and iterate channels.
4. In json_setchannelfee "all" remove useless call to peer_active_channel
since we check state anyway, and iterate.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We don't need to hand it to channeld: it will read it! We simply
need to tell it to expect it.
Similarly, openingd/dualopend will never see it, so remove that logic.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Suggested by @m-schmook, I realized that if we append it later I'll
never get it right: I expect parameters min and max, not max and min!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Changelog-Added: Protocol: you can now alter the `htlc_minimum_msat` and `htlc_maximum_msat` your node advertizes.
We used to calculate it ourselves. Unfortunately this needs to
be done in several places, since new_channel() isn't used to fully
create a channel in the case of dual funding :(
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is neater than what we had before, and slightly more general.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Changelog-Changed: JSON_RPC: `sendcustommsg` now works with any connected peer, even when shutting down a channel.
We now let gossipd do it.
This also means there's nothing left in 'struct per_peer_state' to
send across the wire (the fds are sent separately), so that gets
removed from wire messages too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We need to stash/save the amount of the lease fees on a leased channel,
we do this by re-using the 'push' amount field on channel (which is
technically correct, since we're essentially pushing the fee amount to
the peer).
Also updates a bit of how the pushes are accounted for (pushed to now
has an event; their channel will open at zero but then they'll
immediately register a push event).
Leases fees are treated exactly the same as pushes, except labeled
differently.
Required adding a 'lease_fee' field to the inflights so we keep track of
the fee for the lease until the open happens.
The old model of coin movements attempted to compute fees etc and log
amounts, not utxos. This is not as robust, as multi-party opens and dual
funded channels make it hard to account for fees etc correctly.
Instead, we move towards a 'utxo' view of the onchain events. Every
event is either the creation or 'destruction' of a utxo. For cases where
the value of the utxo is not (fully) debited/credited to our account, we
also record the output_value. E.g. channel closings spend a utxo who's
entire value we may not own.
Since we're now tracking UTXOs onchain, we can now do more complex
assertions about the onchain footprint of them. The integration tests
have been updated to now use more 'chain aware' assertions about the
ending state.
And turn "" includes into full-path (which makes it easier to put
config.h first, and finds some cases check-includes.sh missed
previously).
config.h sets _GNU_SOURCE which really needs to be done before any
'#includes': we mainly got away with it with glibc, but other platforms
like Alpine may have stricter requirements.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It's probably not worth fixing for the other daemons.
Changelog-Changed: JSON-RPC: `ping` now only works if we have a channel with the peer.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Before:
Ten builds, laptop -j5, no ccache:
```
real 0m36.686000-38.956000(38.608+/-0.65)s
user 2m32.864000-42.253000(40.7545+/-2.7)s
sys 0m16.618000-18.316000(17.8531+/-0.48)s
```
Ten builds, laptop -j5, ccache (warm):
```
real 0m8.212000-8.577000(8.39989+/-0.13)s
user 0m12.731000-13.212000(12.9751+/-0.17)s
sys 0m3.697000-3.902000(3.83722+/-0.064)s
```
After:
Ten builds, laptop -j5, no ccache: 8% faster
```
real 0m33.802000-35.773000(35.468+/-0.54)s
user 2m19.073000-27.754000(26.2542+/-2.3)s
sys 0m15.784000-17.173000(16.7165+/-0.37)s
```
Ten builds, laptop -j5, ccache (warm): 1% faster
```
real 0m8.200000-8.485000(8.30138+/-0.097)s
user 0m12.485000-13.100000(12.7344+/-0.19)s
sys 0m3.702000-3.889000(3.78787+/-0.056)s
```
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Typically we forget a channel if 2016 blocks have passed and
the funding transaction hasn't been mined yet, however we
SHOULD NOT forget these channels if we've got funds in them!
Rusty Russell
niftynei
Christian Decker
Ken Sedgwick